Star Micronics Printer Errors (TSP650) for Appetize

Description: Star Micronics printers have two classes of error: Recoverable and Non-Recoverable. The front-panel lights next to the feed button will indicate the device's status. Refer to the table below for the light status and description.

---

The Star Micronics website has visual indicators of the various error messages.  

1. Please follow the link to see the error combinations: Star Micronics Help Center
2. Select the TSP650II Printer option from the left side menu.
3. Once you have identified the issue, please contact Appetize Support to resolve the error.

Recoverable errors

Power light	Error light	Beep code	Issue description	Recommended fix
On	Flashing (On 1 sec/off 1 sec)	4 short beeps repeated twice.	Paper end error	Replace the paper roll in the printer. Be sure to remove the plastic core from the previous roll before installing the new roll. Paper feeds from the bottom of the roll. Consult the supported printers page for paper specifications for your printer.
On	On	Continuous	The top cover of the paper tray is not closed.	Close and latch the top cover of the printer. If the cover is securely latched the printer may be faulty.
Flashes (On: 0.5 sec./Off: 0.5 sec.)	On	Continuous	The front cover (if equipped) is open.	The SP700 impact printer has a second cover on the top of the printer in front of the paper compartment lid. This cover is opened during the ink ribbon installation for this printer. The cover must be closed to resolve this error.
Flashes (On: 1 sec./ Off: 1 sec.)	Off	None	High head temperature detected	Thermal printers use a heated pin array to print on heat-sensitive thermal receipt paper. If the head becomes too hot, the printer will shut down to allow the head to cool to a safe temperature. The error is normal under very heavy use conditions or where the ambient temperature is extremely hot. This is a normal error in those cases.  The printer will recover when the head has cooled sufficiently.
Flashes (On: 2 sec./ Off: 2 sec.)	Off	None	High board temperature detected	The printer's motherboard is too hot. The printer will shutdown to prevent damage to the board. This is unusual unless the printer is located in an unusually hot location or in direct sunlight. Ensure the printer is in a clean, dry and cool location if possible. The printer will recover when the board has cooled sufficiently.
On	Flashes (On: 0.125 sec./Off: 0.125 sec.)	3 short beeps	Cutter error (on models with cutter)	On printers equipped with a paper cutter, the printer will error if the cutter becomes jammed, stuck or fails to operate. Ensure the paper path is clear of jams, shut off the printer and power back on. The error should clear upon power-up. If the error does not clear, the printer may be faulty.
On	Flashes (On: 0.25 sec./Off: 0.25 sec.)	2 short beeps	Mechanical error (other than cutter)	A paper jam usually causes this error. Turn the power OFF, clear the jammed paper, and then power back on. If the issue persists, you may attempt to clean the paper roller on the lid using isopropyl alcohol and a lint-free cloth.
On	Flashes (On: 0.5 sec./Off: 0.5 sec.)	3 short beeps	Black mark detection error	This error can be caused by paper jams as well as incorrect receipt roll sizes.
Flashes at 2-second intervals	Flashes at 2-second intervals	None	Link disconnection detection (Physical link disconnection)	This error occurs only with an Ethernet printer in which the network cable is unplugged or is severed. Connect a known-working cable from the network router to the printer and re-check. If the problem replacement cable does not resolve, try a different port on the network router. Should the issue persist, the printer may be faulty.
Flashes at 0.125-second intervals	Flashes at 0.125-second intervals	None	Link disconnection detection (IP Address lost)	Ethernet printers that fail to obtain an IP address once attached to a working Ethernet cable will display this error. Ensure the Ethernet cable is connected to a working port, that the router is not restricted or otherwise ignoring the device and that sufficient IP addresses in the POS network are available. This error does not indicate a fault in the printer.

 

Non-recoverable errors

Non-recoverable errors are major faults in the device which will require replacement. There are no fixes available for users in-the-field with the below issues:

Power light	Error light	Beep code	Issue Description
Off	Flashes (On: 1 sec./ Off: 1 sec.)	None	Flash memory write error
Off	Flashes (On: 0.25 sec./ Off: 0.25 sec.)	2 short beeps	Thermistor failure error
Off	Flashes (On: 2 sec./ Off: 2 sec.)	None	Power supply error
Off	On	One long beep (2 sec.)	CPU error
Off	On	None	RAM read/write error